Quality Management
Controlled at every step,
consistent batch to batch
Our quality management is built on defined procedures, multi-stage inspection and batch traceability — so what we supply matches the specification agreed for your project. Materials are supplied for research and analytical use only.
Quality Framework
One path from requirement to release
Every project moves through the same sequence of gates and checkpoints. Each step is defined, recorded and traceable to its batch — so quality is built in through the process, not judged at the end alone.
Analyse des besoins
Sequence, format and documentation requirements are confirmed before a project begins.
Material control
Incoming materials are managed and identified so production runs against known inputs.
Process monitoring
Key parameters are monitored through production rather than checked only at the end.
In-process inspection
Checks are recorded at defined points to support consistent, repeatable output.
Final review
Results are reviewed against the agreed specification before material is prepared for release.
Packaging verification
Packaging, labelling and batch identification are verified prior to dispatch.
Documentation
Batch and specification records are compiled to the scope agreed for the project.
Control by Stage
What we check, and when
Control is applied across the production timeline. Here is the focus at each phase — with the specific checks and documents confirmed during specification review.
Before production
Preparation and inputs — confirming scope and managing materials before work starts.
- Specification and project scope confirmed
- Incoming material identity and condition checked
- Documentation requirements agreed
Records: specification review · material control
During production
In-process control — following defined procedures and keeping batch identity.
- Key process parameters monitored
- In-process inspection at defined points
- Batch identity maintained throughout
Records: in-process inspection · process notes
After production
Review and release — checking results against the agreed specification.
- Final review against specification
- Batch checks reflected in documentation
- Any deviation handled through a defined process
Records: final review · deviation (where applicable)
Before shipment
Packaging and records — verifying the shipment is ready and identified.
- Packaging and labelling verified
- Batch identification confirmed
- Documentation set prepared for the project
Records: packaging verification · dispatch prep
Laboratory & Inspection
Where the checks happen
Illustrative views of the environments and equipment involved in inspection and handling. Select any image to view it larger.
Documentation
Records that support your workflow
The documentation prepared depends on project scope. These are the records that may be available — reflecting what was confirmed during technical review.
Specification records
Reflect the specification confirmed during technical review.
Batch-level records
Prepared to the scope agreed for each project, supporting a traceable supply chain.
Inspection records
Checks recorded through production and at final review.
Packaging verification
Packaging, labelling and batch identity verified prior to dispatch.
Additional documentation
Further records as agreed during specification review, subject to project requirements.
Certifications
Certifications & standards
Only certifications the company actually holds are shown here. The items below are placeholders — replace with verified certificates before launch. Nothing below implies a certification has been obtained.
KLOW
Vanguard Laboratory
Reta
Vanguard Laboratory
Freedom Diagnostics
BPC_157+TB500
Tirz
Vanguard Laboratory
Note: Testing follows lab chromatography & mass spec standards. Data for research only; samples not for human, veterinary or clinical use.
Quality Commitments
What we hold ourselves to
A short summary of the principles behind everything above.
Specification-based production
Production runs against a specification confirmed during technical review.
Multi-stage inspection
Checks are recorded across the process, not at the end alone.
Batch consistency
Repeat supply stays aligned to the same agreed specification.
Documented processes
Steps and results are recorded to the scope agreed per project.
Packaging verification
Packaging, labelling and batch identity are verified before dispatch.
Technical coordination
Additional checks and documents are coordinated with your team.
Project-specific Support
Additional checks, arranged around your brief
Where a project calls for more than standard handling, the scope is agreed during specification review. We coordinate additional checks, documentation and packaging based on what your workflow requires.
Availability of any specific test or document depends on project requirements — nothing is assumed by default, and everything is confirmed before work begins.
- Special testing requirementsAdditional analytical checks defined for the project.D'un commun accord
- Spécifications personnaliséesSpecification tailored to your intended use.On review
- Documentation requirementsRecords prepared to an agreed scope.Per project
- Special packagingProtective or specific packaging where required.D'un commun accord
- Sample arrangementsSample handling arranged where applicable.On request
- Technical confirmationScope confirmed with your technical team.On review
Contactez-nous
Questions about quality or documentation?
Tell us what your workflow requires and we will review scope, checks and documentation for your project.